Automark-logo
2

Health And Safety Information

PRODUCTThermoplastic Road Marking Materials

INTENDED USEHorizontal road and airfield markings

COMPOSITION: Synthetic resin, Refined mineral oil, Pigments - Titanium dioxide (white) and Middle Chrome (yellow), Light coloured aggregates, Extenders, Reflective glass beads (reflective grades only), Polymer additives

GENERAL PHYSICAL PROPERTIES

Softening point: Not less than 65°C

Flash point: Exceeds 230°C (Open cup method)

Relative Density: 1.98 +/- 0.02

HEALTH HAZARDS

Powder Form

  • Skin Contact: Low order of toxicity, Low order of irritation, Contact with skin should be minimise
  • Eye Contact: Particles may scratch eye surfaces/cause mechanical irritation
  • Ventilation: Should be used in well ventilated areas
  • Dust long term exposure limit: 10mg/m3 8 hour Time Weighted Average.
  • Ingestion: Essentially non toxic. Ingestion should be avoided

Molten Form

  • Skin Contact : Contact with skin will cause burns and must be avoided
  • Eye Contact : Contact with eyes will cause serious damage and must be avoided
  • Inhalation : Negligible hazard. Should be used in well ventilated areas
  • Ingestion : Ingestion will cause serious harm and must be avoided

NOTE: The Middle Chrome pigment used in the manufacture of yellow thermoplastic road marking material is a low solubility inorganic lead compound

FIRST AID

Powder Form - Action Steps

  • Skin contact : Negligible hazard. Wash with soap and water\
  • Eye contact : i) Flush eyes with large amounts of cold sterile water until irritation subsides.
  •                         ii) If irritation persists seek medical attention.
  • Inhalation : First aid not normally required
  • Ingestion : No hazard in normal industrial use. First Aid not normally required

Molten Form - Action Steps

Skin/Eye contact : 

  • Immediately immerse or flush the affected area with large amounts of cold sterile water to dissipate heat and limit the injury
  • No attempt should be made to remove the thermoplastic or any clothing that may be fused to the damaged area.
  • Seek immediate medical attention and give this information sheet to medical staff.

Inhalation : In normal industrial use, First aid is not normally required for Inhalation of fumes.

Ingestion : Seek immediate medical attention

PRECAUTIONS IN HANDLNG AND USE

  • General : Hot applied thermoplastic road marking material should not be used in its molten form by anybody not formally trained in safe handling procedures.
  • Storage and Transportation : Thermoplastic materials should be stored safely and securely in areas not subject to excessive heat or contamination from fuels, oils or greases. 
  • Personal Protective Equipment : Wear long sleeved flame retardant overalls, industrial, safety shoes/boots. Industrial heat resistant gloves with extended sleeves, gauntlet type. Full face shield for loading and running off preheaters. Use proper respiratory protection when working in areas of poor ventilation.
  • Heating : Ensure that all operatives are fully conversant with equipment manufacturer safety instructions for lighting, feeding and shutting down of preheaters. Maintain equipment in good working order, ensure temperature gauges are accurate and calibrated regularly. Do not overheat material. Do not maintain at working temperature for longer than is necessary (maximum 6 hours). To avoid danger of hot material splashing, great care should be taken when adding material to hot material already in the preheater. Use well charged preheaters but do not overfill, allow for expansion of the molten thermoplastic.

Application : The 'Maximum Application Temperature' and 'Maximum safe Heating Temperature' are marked on our packages in accordance with MOST 803 / BS 3262: Part I. 

EMERGENCY PROCEDURES

Fire : The prime consideration in the event of a fire must be the safety of the operatives and anyone in the immediate vicinity of the fire. The procedures listed below are recommended only when personal safely is not at risk. If the fire cannot be extinguished without endangering personal safely, call the Fire Brigade Immediately.

In the event of a fire in the Preheater : Fire will produce dense black smoke containing harmful products of combustion.

  • Turn off gas or heating source immediately.
  • Turn off agitator and extinguish flames using dry powder or CO2 fire extinguisher.
  • Do not use water at any time, either to extinguish the fire or to cool the preheater.
  • Leave preheater open.Introduce more cold material into the preheater if possible to assist in reducing overall product temperature.
  • Allow to cool, check temperature gauge. Do not drain off material until it has cooled below the maximum safe heating temperature.

Spillag / Escape

In the event of spillage or escape : 

  • If safe to do so - shut off source.
  • Contain the spillage.
  • Allow to solidify before disposal.

ENVIRONMENTAL

Waste material should be disposed of in accordance with local disposal regulations for non hazardous substances.

This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. Such information is to the best of Automark's knowledge and belief accurate and reliable. This information supercedes all previous health and safety information issued by Automark. However, no representation, warranty of guarantee is made as to its accuracy, reliability or completeness. It is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use.

 

 

 

Services


Certification

  • Title : ISO 9001 2000 Certification
    Images :
    Description :

    ISO 9001 2000 Certification

  • Title : ANACON LABORATORIES, NAGPUR
    Images :
    Description :

    ANACON LABORATORIES, Nagpur is a NABIL accredited analytical testing laboratory and now a leading Environmental Consultancy firm in Central India region

  • Title : NATIONAL TEST HOUSE
    Images :
    Description :

    National Test House, Delhi Kolkata and Mumbai, is largest multi-location, multi-disciplinary industrial testing laboratory in India.

  • Title : DELHI TEST HOUSE, DELHI
    Images :
    Description :

    Delhi Test House, Delhi, is one of the largest private testing laboratory in India. Founded in 1975. Focussed on providing high quality analytical services promptly, confidentially on a professionally cost effective man

  • Title : ANU LAB, AGRA
    Images :
    Description :

    Anu Lab, Agra is a NABL accredited testing laboratory Aand the most technically advanced engineering laboratories in India offering a full range of testing and analytical services.

  • Title : Shriram Institute of Industrial Research
    Images :
    Description :

    Shriram Institute of Industrial Research, Banglaore and Delhi, Shriram Institute for Industrial Research (SRI) is an independent, self sustaining, not-for-profit multidisciplinary contract research

  • Title : Laxminarayan Institute of Technology
    Images :
    Description :

    Laxminarayan Institute of Technology, Nagpur, is a premier government aided institute of higher education in the field of chemical engineering and technology.

  • Title : Ministry of Roads, Republic of Kenya
    Images :
    Description :

    Ministry of Roads, Republic of Kenya, also approved the Thermoplastic Road Marking Material confirming KS : 2157 standards.